- Mar 03, 2018
-
-
Tim Niemeyer authored
Signed-off-by:
Tim Niemeyer <tim@tn-x.org> Reviewed-by:
Robert Langhammer <rlanghammer@web.de> Reviewed-by:
Christian Dresel <fff@chrisi01.de> Tested-by:
-
Adrian Schmutzler authored
Signed-off-by:
Adrian Schmutzler <freifunk@adrianschmutzler.de> Reviewed-by:
-
- Feb 13, 2018
-
-
Christian Dresel authored
The simplest and fasted way to Fixes #72 Signed-off-by:
-
- Feb 10, 2018
-
-
Adrian Schmutzler authored
Code which is reused by other functionalities is put into the fff-hoodutils package, so it can be used without including configurehood. This also allows setting missing dependencies of other packages. Signed-off-by:
-
Adrian Schmutzler authored
This addresses a bunch of issues: - Previously, only the presence of w2configap was checked. With only 5 GHz, this would have caused a recreation every 5 min. (Note that this is only valid for a 5 GHz only device, as we always create all interfaces for disabled radios) - The two outer if-statements are merged - We now check for presence of wXmesh to enable wXconfigap. Although this is no necessity (as the hood file contains the whole config) this assumes that a disabled wXmesh means no intent of the owner to connect to other devices on this radio. - With the dependency of wXconfigap from wXmesh, this patch now enables the deactivation of hood file transmitting by disabling meshing in the hood file Signed-off-by:
-
- Jan 28, 2018
-
-
Adrian Schmutzler authored
Bug 1: If devices with hidden SSID are present, the matched SSID in the awk contains the newline (="unknown\n\t"). This destroys the table after the sort. Bug 2: If SSIDs contain ampersands (yes, people do that), they are now converted to &. Signed-off-by:
-
Adrian Schmutzler authored
The actual calculation is done in the Monitoring. Signed-off-by:
Fabian Bläse <fabian@blaese.de>
-
- Jan 21, 2018
-
-
Tim Niemeyer authored
Fixes: #71 Signed-off-by:
-
Adrian Schmutzler authored
This adds data about the clients per interface Signed-off-by:
-
Fabian Blaese authored
Since the reverted patch, device specific antenna gain is not set for some reason. Reverting the patch in question fixes this issue. THIS SHOULD BE ONLY CONSIDERD AS A TEMPORARY FIX UNTIL THE ISSUE IS FIXED PROPERLY! Fixes: #85 Signed-off-by:
-
Adrian Schmutzler authored
This is a workaround to enable alfred on routers which do not see a configap during initial boot. Fixes: #78 Signed-off-by:
-
Adrian Schmutzler authored
The AR150 seems to have the same MAC address on eth0, eth1 and phy0. Although it is not a ONEPORT, we can use the shifted bit like for the ONEPORT devices to get a distinct ETHMESHMAC. Signed-off-by:
Jan Kraus <mayosemmel@gmail.com>
-
- Jan 20, 2018
-
-
Adrian Schmutzler authored
Signed-off-by:
-
Adrian Schmutzler authored
Instead of using the hiddenapflag file, we can just check whether the hood file copy used by the webserver is present. As a second condition, we check whether the w2configap is not configured yet. This fixes the following minor issue: Previously, if configurehood has run once, the hiddenapflag was set, but the configap not set up yet. If then a restart happens, the flag is gone (/tmp), but not recreated until a change in the hood file appears. Thus, no configap would be set up until that point. Since we check for a real condition now, this can't be happening. Signed-off-by:
-
Adrian Schmutzler authored
Changes: - Remove first line (headline) previously parsed as gateway - Delete leading whitespaces for netif correctly (regex "\\[" changed to "\\[ *") - Remove netif whitespaces first, so they are not changed to "false" - Include trailing whitespace in regex for selection marker - Remove useless replacement " " to " " This is designed to support BATMAN compatibility version 14 AND 15 Signed-off-by:
-
Adrian Schmutzler authored
If the mac is read from /sys/class/net/${iface}/address, some devices (WA860RE, Picostation) will not set the fdff addresses. This can be fixed by using the $ROUTERMAC in configurenetwork. Signed-off-by: -
Adrian Schmutzler authored
Previously, IPv6 addresses were constructed by reading from the device config file in the function. To have more options, it is better to use the address itself as parameter. By this way we can decide what we use for getting the MAC when calling. Signed-off-by:
-
Adrian Schmutzler authored
This is a cosmetical patch, however it does increase the overview a lot in my opinion. We cannot drop the special case of the two-port devices, because we need the current setup to enable setting port mode in the Web UI. Signed-off-by:
-
Christian Dresel authored
Add a complete hoodfile to /etc/hoodfile to use only this file Signed-off-by:
-
- Jan 03, 2018
-
-
Adrian Schmutzler authored
After the remerge the LEDE git source is broken, thus we switch to the OpenWRT sources. Signed-off-by:
-
- Dec 31, 2017
-
-
Adrian Schmutzler authored
This patch additional information to the nodewatcher XML: - wlan_channel: Channel of interface (number only) - wlan_ssid: SSID available through iw dev - wlan_type: Type of interface (AP, mesh, IBSS) - wlan_width: Width of frequency band (20 vs. 40 MHz, number only) The nodewatcher file from this patch can be copied manually to devices with older firmware. The patch includes some comment typo fixes. Signed-off-by:
-
- Dec 23, 2017
-
-
Adrian Schmutzler authored
To prevent connecting hoods, this patch loads keyxchange files from the local network (eth0.3/eth0) before it uses the gateway. Thus, if other files are provided via wXconfigap, they are just ignored. If a router is connected to two hoods by cable, it will just disable the interfaces where a second hood file is detected and wait until the next call of configurehood. If cable and wXmesh are different, the cable has precedence. If two hoods are present via cable on the same eth, wXmesh has precedence. If two hoods are present via cable on different eth, the first eth has precedence and all others are disabled. If cable has precedence, wXmesh is configured with the hood file from cable. Signed-off-by:
-
Adrian Schmutzler authored
The configurehood script is started at the same time for all routers. Thus, if one router sets up its configap, another may just go into wXsta at the very same moment. This creates a race condition between configap setup and wXsta download. To circumvent this, we add a sleep to the wXsta routine, so the wXsta always comes later, but is still run every 5 minutes. Signed-off-by:
-
Christian Dresel authored
This is the correct firmware for the Unifi AC Mesh I have only tested at Unifi AC Mesh and not at Unifi AC lite But my information is, that both have the same Hardware Signed-off-by:
-
Robert Langhammer authored
We need the new tunneldigger because the old broker no longer works with the current kernel. Signed-off-by:
-
Adrian Schmutzler authored
Since we change only the network part of uci, we only need to commit this part and not the whole config five times. Signed-off-by:
-
Adrian Schmutzler authored
Signed-off-by:
-
- Dec 22, 2017
-
-
Adrian Schmutzler authored
Signed-off-by:
-
Robert Langhammer authored
We do not use encrypted tunnels, so we can use urandom generating the keys to prevent blocking due to low entropy. Signed-off-by:
-
- Nov 13, 2017
-
-
Adrian Schmutzler authored
Signed-off-by:
-
- Nov 12, 2017
-
-
Adrian Schmutzler authored
This includes the new options introduced due to the /etc/config/fff file into the WebUI. Signed-off-by:
-
Adrian Schmutzler authored
Update notification is enabled by default. If required, this allows disabling it permanently. Signed-off-by:
-
Adrian Schmutzler authored
This implements an upgrade safe solution for the PoE passthrough on multiple devices. Since LEDE already provides the relevant settings, a check whether those are in place enables both identification of affected devices and automatic deactivation if parameters are changed. Signed-off-by:
-
Adrian Schmutzler authored
This moves the FFF configuration from /etc/config/system to a new file /etc/config/fff. Thus, this file can be copied as a whole during upgrade (with compatibility provided) and then resulting values in other files are re-set later. This also fixes the bandwidth settings not being persistent during upgrade. Other settings may join ... I tried to go through all the code and update all occurrences of the relevant system variables (looking for "system" both in GitHub and my local src folder). Note that a downgrade will result in loss of configuration! Signed-off-by:
-
Adrian Schmutzler authored
Signed-off-by:
-
Adrian Schmutzler authored
This patch introduced more detailed information about the hood in the WebUI, i.e. channel and SSIDs. The patch includes a reorganization of the columns. Signed-off-by:
-
Adrian Schmutzler authored
Signed-off-by:
-
Fabian Blaese authored
This adds missing ROUTERMAC variable for CPE510 Signed-off-by:
-
Fabian Blaese authored
Using wifi devices makes it possible to get mac address without having to configure wifi networks. Signed-off-by:
-
Tim Niemeyer authored
During system boot, the dependency of alfred to the bat0 interface is problematic. In some circumstances (no eth mesh and no wifi mesh), the mesh interfaces are disabled, the bat0 interface is removed and the station mode is entered. Because alfred is started after the station mode (current boot order), it doesn't start up with the missing bat0 interface. Signed-off-by:
-
